Rotate the pulley teeth and pop the chain into place. The kit will come complete with detailed instructions, so you'll be enjoying your window treatments again in no time flat.
Now you need to cut the string from the bottom end.
How to fix broken blinds pull cord. With one hand guiding the cord splice through the slats and headbox hardware, pull on the old lift cord. How to repair the pull string for vertical blinds. Then pull the string towards the pulley over the locking mechanism and slip it down through the locking mechanism.
If this is the case, use a screwdriver to remove the cover. You can do this with your hands and fingers. Thread one end of the chain up through the guard.
Pull roughly ten feet of the cord through the locking mechanism. Look for the end of the cord, where it is tied in a knot. Pull the chain through the clutch.
Whatever the case may be, you don't always have to replace the entire window covering just because your cord is broken. With the replacement cord in hand, take one end and attach it to the broken end of the cord. Remove the head rail cover from the head rail.
In other cases, the head rail remains exposed. Remove the wooden cap bead from the end of the cord and trim off any snarls so you have a neat end. Put the shade back to the window.
Before cutting the string, take a buffer of about 12 inches below the bottom rail. How to fix a broken roller blind chain. If you live with a cat, chances are the cords on your horizontal blinds have been used as a chew toy.
Customer service will reference this number to determine how much cord is needed. If the cord is broken or missing, replace the cord with a new piece. Fixing a broken pull cord you will need the new pull cord, as well as a lighter and, potentially, some masking tape for this fix.
Thread new strings through the shade. Pull the string through the hole and untie the knot. However, at times, they get trapped, which makes it tricky to lower them.
Pull the cord toward you, and cut the knot off the end of the cord. This damage may even have rendered your blinds unusable as either the cords are now too short or. The tassel needs to be unscrewed and set aside.
Clip any excess fray from the end of the cord. Loop the two ends of the broken string together to form a small knot. While the blind is still hung (fig.
Remove the head rail cover from the head rail. Take a restringing needle and thread the new string through it. How do you fix the cord on honeycomb blinds?
Use a flathead screwdriver to remove the two (or more) plugs at the bottom of the blinds that hold and cover the lift strings or the thicker center string. Remove the cap covering the hole in the bottom rail of the venetian blinds. Thread the string up through the hole in the bottom of the head rail if the string fell out.
Carefully pull on the old cord at the other end, pulling the new cord into the blind, while feeding the new cord in and gently helping the joint go through the holes in the blinds, then into the top rail. Replace the broken slat and then restring the lift cord through each slat from the blind. Sometimes a chain will simply snap due to wear and tear or because the blind has been fitted too tightly inside the brackets, causing the linking pin to come loose and drop out.
When the splice is clear of the headbox, draw the new lift cord to the bottom bar, undo the splice and attach any plastic pulls on the end of the new cord. When you pull the cord to tilt the slats and the slats do not tilt, that indicates that the tilt mechanism is broken and needs to be replaced. Locate the break in the string inside the head rail.
Home & garden, blog a common problem with roller blinds is a broken chain. Blinds can be readily pulled up to allow more light into the room. The cord tilting string is broken, uneven or pulled out.
Once the joint appears out of the upper rail on the other side, you are done. Don't start pulling the broken cord or tassels yet. Undo the knot of this lift cord and pull on the cable out of the front of the blind.
Press the chain into the pulley teeth. How do i replace the pull cord on my hunter douglas blinds? In some cases, the head rail cover secures into place with screws.
Take hold of the broken end of the cord that travels up into the headrail. If this is the case, use the ladder so you can see down into the head rail.