Use more strokes if the chainsaw has hit a nail or has been cutting muddy wood, as both actions will dull the chain more. You can sharpen a chainsaw chain by hand with a file, or by using a tool.
By hand with a file sharpener;
How to sharpen a chainsaw with a file. The length between the thread rivets is found and divided by 2. To sharpen a chainsaw by hand follow these steps: After filing the gullet (slot under the cutter) of the cutter with a round file, put the depth gauge guide on top of the filed cutter and position its slot on the depth gauge.
You may decide to use a flat file to measure correctly and ensure that the teeth are of a similar height. Look through the file guide The other important thing here is the chainsaw file or rotary grindstone.
Once you know the right position, place the file and push it through the cutter. Here, we recommend using a file with a diameter of the same or slightly bigger size than the cutters. Sharpening the cutters step 1:.
Switch the chain to the other side and file when you are done to sharpen both sides. Grab the file and prepare. Tips for properly sharpening a chainsaw.
Once you’re done with one area of the chain, reposition it by letting go of the chain brake and fixing it again once you’re ready. Learn about your chainsaw’s gauge and get the right tool for it. Set the handle of the file guide at 30 degrees according to the husqvarna chainsaw chain sharpening angles if you want to sharpen the saw chains at that angle for the best results.
Set your depth gauge and measure teeth at the front and back to check the depth and see if it is the correct height. By hand with a power dremel; The most affordable, but long enough way to return the chainsaw to working condition is a file.
Once you start turning the chain and reach the first cutter, you know it’s finished. How to sharpen a chainsaw by hand. When that happens, you need to sharpen each of the chainsaw blade’s individual blades to make the tool work like new again.
Usually, you use a file to sharpen the blades and then go through each one until all are done. Asses where the chainsaw rollers are and make sure to be holding your round file at a 90 degree angle from them. Alternatively, you can measure the slope of the chain.
Be sure to mark your starting point on the chain. It might seem rough to file a chainsaw chain by hand, but it’s one of the most common and cheapest ways. Do this a few times, without excessive pressure, but remember to always go forward.
Filing by hand is difficult enough as it is, but this method also requires that the tilt and top plate angles be maintained visually throughout the procedure by the person sharpening. Both methods are not difficult and will result in a sharp and good working chainsaw. To properly sharpen chainsaw chain you will need:
For this, you will require a flat file. Either one of these items is needed in order for you to sharpen your chainsaw like a pro. How to sharpen a chainsaw chain.
Keep the file in line with the file holder across the bar at an angle needed for your saw and keep the file very very level too. When the blue line is well aligned and parallel to the chains, begin to grind on a pull. The number of blades in a chainsaw makes sharpening time consuming.
If there is a protrusion of the top of the depth gauge on the slot, this is the part that you need to file out using a flat file. Once you are done with one set, go ahead and turn the chainsaw 180 degrees and sharpen the next type of cutters. This is answered comprehensively here.
You then assign this number to the file size listed in the file scheme. To sharpen the limiter itself, they resort to using a flat file. But not every kind of file or grindstone is suitable for your chainsaw.
With the cutters identified, you can grab the round file and proceed to check how you’re going to sharpen. Pitch is measured in inches. Chainsaw sharpening and chainsaw filing is very important as a dull chain increases the risk of kickback, fuel consumption, and excessive damage.
To find a round file, you need to know the chain size. You can find the best chainsaw sharpeners here that include all three types. A file guide, flat file, and depth gauge tools (rakers and drags).
File the same number of strokes per tooth. Make sure the gauge has contact with the chain. To convert the result to inches, multiply the result by 0.039.
Stroke away from your body; Different types of chainsaw files and gauges chainsaw file size File the cutting tooth away from you, with smooth strokes.
Going backward with your file will damage the cutters and the file itself. To properly sharpen a chainsaw chain with a round file, the file must be held perfectly parallel to each tooth's tilt and top plate angles while being filed. The pitch of a file is the distance measured between three rivets, then divided by two and it is indicated in inches.
The file size simply matches the depth gauge code number, alternative depth gauge markings, or pitch of a chain to the right file size. You can then use the graph to get the right file. Sharpen every second cutter from the first marked one, working on each 3 to 10 times.
And then file away till you can rest assured that the chainsaw is sharpened. Here is a link to the one that i bought: Follow these steps to sharpen a chainsaw chain quickly and accurately.
The file should rest on both rollers. A file chart is used to determine the size of the file that will sharpen the cutter correctly. There are three ways to sharpen a chainsaw: