Trim any excess fabric to make it easier. Pull the batting in the center of one of the sides snugly up and over the foam and plywood and use a staple gun to staple it to the plywood.
Lay the piece of fabric on the floor, and turn the bench over on the fabric.
How to upholster a bench with a back. And the fabric can be suited to match the rest of the dining set, keeping to continuity. How to upholster a storage bench: The final step to reupholster a bench is to attach your newly covered bench seat to the frame.
Fill all holes and seams with wood putty. I bought this beautiful green velvet fabric to upholster the bench seat with. Use one staple every 2 inches or so.
Cut a generous amount of fabric all around the seat to ensure there’s enough for stapling. And guess what in the end, i didn’t “ruin” it at all. Upholstered dining bench with back.
An upholstered dining bench with a back is a soft and comfortable replacement for the wood, unpadded bench some bistro dining sets come with. Place upholstery fabric face down, then insulating fabric, then bench top (all face down on a large, flat working surface). Repeat for an adjacent side.
Anyway, long story short, this bench was one of the pieces that took some convincing to change. To separate the two parts of the seat, pull off the hinge cover trim pieces on the back bottom edges to get access to the hinge bolt. I don’t have a photo of this step, but basically it should look like the spacers that were added to support the bottom shelf.
This tufted linen fabric ottoman bench is a luxury option that would suit more opulent dining rooms. If you want to make a soft seat for your bench, you can upholster it with some simple tools. For the back of the bench, i had to bevel the cut at a 45 degree angle to ensure the bench would fit under the battens.
Elegant finials on the sides and arms with a back motif inspired by gothic architecture transform its pine wood frame into a striking statement appropriate for any interior. I was strategically able to change the bench with new fabric without damaging any of the existing (just in case he wants to have it back to what it used to look like). Once the spray adhesive dried, i laid out the upholstery fabric and turned the bench over (foam side down).
Use a hammer to set the staples flush with the board. You can either staple the batting first and then the fabric, or you can do the two of them at the same time, which i did ’cause i wanted to be done. Position the foam on top of the plywood so that all the edges are lined up, then gently press.
So, i just sort of lined the seat up. How to upolster the bench seat. Flip the piece so you’re looking at the bottom of the bench.
With utility knife, carefully cut off the excess overhang of the upholstery foam. Put the plywood on the drop cloth, and coat the entire surface of the plywood with spray adhesive. Just like step 4, flip the bench seat over face down onto the fabric.
Wrap the extra fabric to the bottom and stretch it so that it lays taut. The problem with the way i covered the bench seat is that there is a lot of material in each corner that covers the original holes. You can see that i stapled the batting in some areas just to secure it.
Pull apart the two pieces, placing the seatback to the side. This bench is available with the cushion in. Wrap and staple the insulating fabric to the plywood bench top.
Using the air stapler, begin to staple the batting to the plywood, pulling it tight as you move around the seat. Add 2 of the 7″ long, 2″ x 2″ wood pieces in between the front and back boxes of the bench. Cut around the perimeter and.
Place the foam and board on the back side of fabric. First, remove your bench’s legs so you can wrap the bench fully. The hampton bench takes a classic garden form and transports it indoors.
Pull the batting snugly and staple on either side of the center staple, a few inches apart. You’ll need foam a little larger than your bench’s surface, and batting and fabric twice the size. Sit with ease and never have a sore posterior after a meal.
Place the bench seat on a sturdy workbench or table. Then remove the bolts on both sides. The tops of them should be flush with the top of the front and back boxes.
Place the newly upholstered bench top on the base. Then, cut the foam to the size of your bench’s. Trim away all excess fabric, you want a smooth bottom before setting the seat on the bench.
Step 5 // repeat the previous step with the fabric. Flip it over and center it on the bench. The frame is made of durable rubberwood while the top is constructed from comfortable memory foam covered in linen.
Wrap one side of the fabric and batting up over its respective edge of the bench, securing it to the underside of the bench with a staple gun. First, pop the lining inside the storage bench and fold the outer cover around the box.